112 lines
4.0 KiB
C
112 lines
4.0 KiB
C
#ifndef __BSP_IO_DEV_H__
|
||
#define __BSP_IO_DEV_H__
|
||
|
||
#include "drv_gpio.h"
|
||
#include "agile_led.h"
|
||
|
||
|
||
|
||
extern agile_led_t *led_r;
|
||
extern agile_led_t *led_g;
|
||
extern agile_led_t *led_y;
|
||
extern agile_led_t *emv;//电磁阀
|
||
extern agile_led_t *fj;//风机
|
||
|
||
|
||
#define LED_ON(x) agile_led_on(led_##x)
|
||
#define LED_OFF(x) agile_led_off(led_##x)
|
||
#define LED_TOGGLE(x) agile_led_toggle(led_##x)
|
||
|
||
|
||
// #define EMV_ACT do{\
|
||
// rt_pin_write(EMV_LED_PIN, PIN_LOW);\
|
||
// rt_thread_mdelay(100);\
|
||
// rt_pin_write(EMV_LED_PIN, PIN_HIGH);\
|
||
// rt_thread_mdelay(100);}while(0)\
|
||
|
||
// #define FJ_ON do{rt_pin_write(FJ_LED_PIN, PIN_HIGH);}while(0)
|
||
// #define FJ_OFF do{rt_pin_write(FJ_LED_PIN, PIN_LOW);}while(0)
|
||
|
||
|
||
//#define EMV_ON(x) agile_led_on(x)
|
||
//#define FJ_ON(x) agile_led_on(x)
|
||
|
||
//电磁阀控制采用N沟道MOS管，高电平导通
|
||
|
||
//#define EMV_OFF(x) agile_led_off(x)
|
||
//#define FJ_OFF(x) agile_led_off(x)
|
||
|
||
#define LED_START(x) agile_led_start(led_##x)
|
||
//#define EMV_START agile_led_start(emv)
|
||
|
||
|
||
#define DEV_CTRL(x, light_mode, loop_cnt) do \
|
||
{ \
|
||
agile_led_set_light_mode(x, light_mode, loop_cnt); \
|
||
agile_led_start(x); \
|
||
} while (0U)
|
||
|
||
|
||
#define LED_STOP(x) do \
|
||
{ \
|
||
LED_OFF(x); \
|
||
agile_led_stop(led_##x); \
|
||
} while (0U)
|
||
|
||
#define LED_CTRL(x, light_mode, loop_cnt) do \
|
||
{ \
|
||
agile_led_set_light_mode(led_##x, light_mode, loop_cnt); \
|
||
} while (0U)
|
||
|
||
|
||
/************************预设的一些LED闪烁模式**************/
|
||
// 预热绿灯闪烁
|
||
#define GREEN_LED_PREAT do \
|
||
{ \
|
||
LED_STOP(r); \
|
||
LED_STOP(y); \
|
||
LED_CTRL(g, "500,500", -1); \
|
||
LED_START(g); \
|
||
} while (0U)
|
||
|
||
// 正常绿灯常亮
|
||
#define GREEN_LED_NORMAL do \
|
||
{ \
|
||
LED_STOP(r); \
|
||
LED_STOP(y); \
|
||
agile_led_stop(led_g); \
|
||
LED_ON(g); \
|
||
} while (0U)
|
||
|
||
// 故障状态 黄灯常亮
|
||
#define YELLOW_LED_FAULT do \
|
||
{ \
|
||
LED_STOP(r); \
|
||
LED_STOP(g); \
|
||
LED_ON(y); \
|
||
} while (0U)
|
||
|
||
// 报警状态 红灯闪烁
|
||
#define RED_LED_ALAEM do \
|
||
{ \
|
||
LED_STOP(g); \
|
||
LED_STOP(y); \
|
||
LED_CTRL(r, "200,200", -1); \
|
||
LED_START(r); \
|
||
} while (0U)
|
||
|
||
// 寿命到期状态 黄灯闪烁
|
||
#define YELLOW_LED_END_OF_LIFE do \
|
||
{ \
|
||
LED_STOP(r); \
|
||
LED_STOP(g); \
|
||
LED_CTRL(y, "500,500", -1); \
|
||
LED_START(y); \
|
||
} while (0U)
|
||
|
||
|
||
|
||
|
||
#endif //!__BSP_LED_H__
|
||
|